GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Kirish

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Xavfsizlik ma'lumotlari

OGOHLANTIRISH: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• O'rnatishdan oldin elektron to'xtatuvchida quvvat O'CHIQ ekanligiga ishonch hosil qiling.
• Ushbu qurilma Milliy elektr kodeksi va mahalliy qoidalarga muvofiq o'rnatish uchun mo'ljallangan.
• Do not use in wet locations or where directly exposed to water.
• Faqat ichki foydalanish uchun.

Paket tarkibi

• GoControl WS15Z5-1 Z-Wave Wall Switch
• O'rnatish vintlari
• Wire Nuts (may vary by package)
• Foydalanuvchi uchun qo'llanma (ushbu hujjat)

O'rnatish va o'rnatish

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Turn OFF Power: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Eski kalitni olib tashlang: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Simlarni aniqlang:
   • Line (Hot): Usually black, coming from the circuit breaker.
   • Yuklash: Usually black, going to the light fixture or appliance.
   • Neytral: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Yer: Odatda yashil yoki yalang'och mis.
4. Yangi kalitni ulang: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • ni ulang Chiziq wire to the terminal marked "LINE".
   • ni ulang Yuklash wire to the terminal marked "LOAD".
   • ni ulang Neytral wire to the terminal marked "NEUTRAL".
   • ni ulang Tuproq wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. O'rnatish tugmasi: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. Devor plitasini o'rnatish: Attach the new or existing wall plate.
7. Quvvatni tiklash: O'chirish to'xtatuvchisida quvvatni qayta yoqing.

1-rasm: Old view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle bir marta. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Kommutatorni ishlatish

Qo'lda boshqarish

• ni bosing yuqori of the paddle to turn the connected load ON.
• ni bosing pastki of the paddle to turn the connected load O'CHIRIB.

Z-to'lqinli boshqaruv

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Xizmat

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Tozalash: To clean the switch, wipe it with a soft, damp mato. Abraziv tozalash vositalarini yoki erituvchilarni ishlatmang.
• Dasturiy ta'minotni yangilash: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Umumiy parvarish: Kalitning haddan tashqari namlik yoki yuqori harorat ta'siriga duchor bo'lmasligiga ishonch hosil qiling.

Muammolarni bartaraf qilish; nosozliklarni TUZATISH

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle bir marta. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Texnik xususiyatlari

Kafolat va qo'llab-quvvatlash

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl websaytga yoki mijozlarga xizmat ko'rsatish bo'limiga murojaat qiling.

Websayt: www.gocontrol.com

Ishlab chiqaruvchi: GOCONTROL