Mopar 68525329AC

Mopar 68525329AC Semi-Metallic Front Disc Brake Pads

Foydalanuvchi uchun qo'llanma

1. Kirish

This manual provides essential information for the proper installation, use, and maintenance of your Mopar 68525329AC Semi-Metallic Front Disc Brake Pads. These brake pads are designed to deliver reliable stopping power and durability for compatible vehicles.

2. Xavfsizlik ma'lumotlari

OGOHLANTIRISH:

  • Brake system work should only be performed by qualified personnel. Improper installation can lead to brake failure and serious injury or death.
  • Avtomobil tormoz tizimlarida ishlayotganda har doim xavfsizlik ko'zoynaklari va qo'lqoplar kabi tegishli shaxsiy himoya vositalarini (SHV) taqing.
  • Brake dust may contain hazardous materials. Avoid inhaling dust and use proper disposal methods.
  • Har qanday ishni boshlashdan oldin, transport vositasi domkrat stendlarida mustahkam tarzda qo'llab-quvvatlanganligiga ishonch hosil qiling. Hech qachon faqat jakka tayanmang.
  • Muayyan moment xususiyatlari va protseduralari uchun avtomobilingizning xizmat ko'rsatish qo'llanmasiga qarang.

3. Paket tarkibi

O'rnatishni boshlashdan oldin barcha komponentlar mavjudligini va buzilmaganligini tekshiring.

  • 2 x Mopar 68525329AC Semi-Metallic Front Disc Brake Pads (set for one axle)
  • Brake hardware kit (shims, clips, etc., as applicable)
Mopar 68525329AC Semi-Metallic Front Disc Brake Pads and packaging

Figure 1: Contents of the Mopar 68525329AC Brake Pad Kit, showing the brake pads, associated hardware, and the Mopar branded packaging.

4. O‘rnatish (Sozlash)

This section outlines the general procedure for replacing front disc brake pads. Always consult your vehicle's specific service manual for detailed instructions and torque specifications.

  1. Avtomobilni tayyorlang: Avtotransportni tekis yuzaga qo'ying, to'xtash tormozini torting va orqa g'ildiraklarni to'sib qo'ying. Old g'ildirakning gaykalarini bo'shating.
  2. Lift va xavfsiz: Safely lift the front of the vehicle using a jack and support it securely with jack stands. Remove the front wheels.
  3. Kirish kaliper: Locate the brake caliper. Depending on your vehicle, you may need to remove two caliper guide pins or bolts to swing the caliper open or remove it entirely.
  4. Eski plitkalarni olib tashlang: Carefully slide out the old brake pads from the caliper bracket. Note their orientation.
  5. Tozalash va tekshirish: Clean the caliper, caliper bracket, and rotor surface thoroughly. Inspect the brake rotor for excessive wear, scoring, or cracks. Replace if necessary. Inspect caliper guide pins and boots for damage.
  6. Pistonni siqish: Use a brake caliper piston compression tool to slowly and evenly push the caliper piston(s) back into the caliper bore. This creates space for the new, thicker pads.
  7. Yangi uskunani o'rnatish: Install any new shims, clips, or anti-rattle springs provided in the hardware kit onto the new brake pads or caliper bracket as per your vehicle's manual.
  8. Yangi prokladkalarni o'rnatish: Carefully slide the new Mopar brake pads into the caliper bracket, ensuring they are correctly seated and oriented.
  9. Kaliperni qayta yig'ish: Reinstall the brake caliper over the new pads and rotor. Secure the caliper guide pins or bolts, tightening them to the manufacturer's specified torque.
  10. Qon ketish tormozlari (agar kerak bo'lsa): If the brake lines were opened or air entered the system, bleed the brake system according to your vehicle's service manual.
  11. Reinstall Wheels: Reinstall the wheels and hand-tighten the lug nuts.
  12. Pastki avtomobil: Safely lower the vehicle to the ground.
  13. Yakuniy moment: Torque the lug nuts to the vehicle manufacturer's specifications in a star pattern.
  14. Pump Brake Pedal: Before driving, slowly pump the brake pedal several times until a firm pedal feel is achieved. This seats the pads against the rotor and restores hydraulic pressure. Check the brake fluid reservoir level.

5. Bedding-In Procedure (Operating)

Proper bedding-in is crucial for optimal brake performance and longevity. This process transfers a thin, even layer of friction material from the pads to the rotor surface.

  1. Minimal trafik bilan xavfsiz, ochiq maydonni toping.
  2. Perform 10-15 moderate stops from approximately 30-40 mph (50-65 km/h) down to about 5-10 mph (8-16 km/h). Do not come to a complete stop.
  3. Allow approximately 30 seconds between stops for the brakes to cool slightly.
  4. After the last stop, drive for several minutes without using the brakes to allow them to cool completely. Avoid hard braking during this cool-down period.
  5. During the bedding-in process, you may notice some smoke or a burning smell. This is normal.

MUHIM:

Avoid heavy braking, panic stops, or prolonged braking (e.g., down a long hill) for the first 200-300 miles (320-480 km) after installation to allow the pads to fully seat.

6. Xizmat ko'rsatish

  • Doimiy tekshirish: Inspect brake pads, rotors, and fluid levels regularly as part of your vehicle's recommended maintenance schedule.
  • Yostiqcha kiyish: Replace brake pads when the friction material wears down to the minimum thickness specified by your vehicle manufacturer, typically around 2-3mm.
  • Tormoz suyuqligi: Ensure brake fluid is at the proper level and is clean. Consult your vehicle manual for brake fluid replacement intervals.
  • Rotor holati: Check rotors for warping, deep grooves, or cracks. Replace or resurface rotors as needed when replacing pads.

7. Umumiy muammolarni bartaraf etish

AlomatMumkin sababYechim
Shiqillagan/silliqlash shovqiniNew pads not bedded-in, worn pads, foreign object, improper installation, worn rotors.Perform bedding-in procedure. Inspect pads for wear. Check for debris. Re-install correctly. Inspect/replace rotors.
Vibration/Pulsation during brakingWarped rotors, uneven pad transfer, caliper issues.Inspect/replace rotors. Re-bed pads. Check caliper for sticking.
Yumshoq yoki shimgichli tormoz pedaliAir in brake lines, low brake fluid, master cylinder issue.Bleed brake system. Check fluid level and leaks. Consult a mechanic for master cylinder issues.

8. Texnik shartlar

  • Brend: Mopar
  • Model raqami: 68525329AC
  • Material: Yarim metall
  • Avtomatik qismning joylashuvi: Old
  • Xususiyatlari mos: OEM
  • Ishlab chiqaruvchi: Stellantis
  • Elementlar soni: 2 (per kit)

9. Kafolat haqida ma'lumot

Mopar parts are backed by a limited warranty. For specific warranty terms and conditions, please refer to the official Mopar warranty documentation provided with your purchase or visit the official Mopar websayt. Kafolat da'volari uchun xaridingizni tasdiqlovchi hujjatingizni saqlang.

10. Mijozlarni qo'llab-quvvatlash

For technical assistance, installation questions, or warranty inquiries, please contact your authorized Mopar dealer or visit the official Mopar support websayt. Batafsil ma'lumot va aloqa ma'lumotlarini sahifada topishingiz mumkin Mopar Store on Amazon.

© 2025 Mopar. All rights reserved. Information subject to change without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.