GEPRC Cinelog30 V3

GEPRC Cinelog30 V3 O4 Air Unit Pro FPV Drone (PNP) Instruction Manual

O'rnatish, ishlatish va texnik xizmat ko'rsatish bo'yicha to'liq qo'llanma.

1. Mahsulot tugadiview

The GEPRC Cinelog30 V3 O4 Air Unit Pro is a high-performance FPV drone designed for professional-grade aerial videography and dynamic flight. It features an O4 Pro Air Unit for ultra-sharp 4K/120fps footage, an aluminum-reinforced frame for durability, and a TAKER F722 45A AIO flight system for responsive handling.

GEPRC Cinelog30 V3 O4 Air Unit Pro FPV Drone

Rasm 1: Yuqoridan pastga view of the GEPRC Cinelog30 V3 O4 Air Unit Pro FPV Drone, showcasing its orange protective frame and black carbon fiber components.

2. Kiritilgan komponentlar

Quyidagi barcha komponentlar paketingizga kiritilganligini tekshiring:

  • 1 x Cinelog30 V3 FPV Drone
  • 1 x Protective Frame (transparent black)
  • 2 x HQprop DT76mmx3 V2 (pair) - Zaxira parvonalar
  • 1 x 15*150mm Battery Strap
  • 1 x L shaklidagi 1.5 mm tornavida
  • 1 x Grey Canopy
  • 1 x Black Canopy
  • 1 x Spare Screw Pack (includes M2 rivet nut, M2*4.5, M2*6, M2*4 button-head hex socket screws, M2*12 button-head screw, 2 x Damping Ball)
  • 1 x Battery Anti-slip Pad
  • 1 x Damping Ball Puncher
  • 1 x Frequency Pairing Ejector pin

3. Dastlabki sozlash

3.1 Droneni ochish

Carefully unfold the drone arms. Always unfold the front arms first, then the rear arms. Ensure they click securely into place.

GEPRC Cinelog30 V3 FPV Drone unfolded

Rasm 2: Burchakli view of the GEPRC Cinelog30 V3 FPV Drone with its arms unfolded, ready for flight.

3.2 Propeller Installation (If Required)

The drone comes with propellers pre-installed. If replacement is needed, ensure correct orientation. Match the propeller rotation direction to the motor direction. Use the provided L-shaped screwdriver for secure attachment.

3.3 Batareyani ulash

Connect a fully charged LiHV 4S 660mAh-720mAh battery (not included) to the XT30 connector on the drone. Secure the battery using the provided battery strap and anti-slip pad.

3.4 Canopy Installation

Choose between the grey or black canopy and securely attach it to the drone frame. Ensure it does not obstruct any sensors or the camera.

4. FPV System Setup (O4 Air Unit Pro & Goggles)

The Cinelog30 V3 is equipped with the O4 Air Unit Pro for high-quality digital FPV transmission. For optimal experience, it is recommended to use compatible FPV goggles, such as the DJI Goggles 3.

4.1 Jonliview Sharing with DJI Goggles 3

The DJI Goggles 3 allow for live view sharing to a mobile device or other goggles. This feature is useful for co-pilots or spectators to view the drone's feed.

Video 1: This video demonstrates how to set up live view sharing from DJI Goggles 3 to a mobile device or other compatible goggles, allowing multiple users to see the drone's real-time camera feed.

For detailed instructions on connecting and sharing live view with DJI Goggles 3, please refer to the video above. Ensure your mobile device has the DJI Fly app installed and that Wi-Fi and Bluetooth are enabled for wireless connections.

5. Foydalanish bo'yicha ko'rsatmalar

5.1 Parvoz oldidan tekshiruvlar

  • Ensure all arms are fully extended and locked.
  • Check propellers for any damage and ensure they are securely fastened.
  • Verify battery is fully charged and securely attached.
  • Confirm FPV goggles and remote controller are powered on and connected.
  • Perform a visual inspection of the drone for any loose parts or damage.

5.2 Uchish va qo'nish

Place the drone on a flat, open surface, clear of obstacles. Follow your remote controller's specific instructions for arming motors and initiating take-off. For landing, gently descend the drone to a clear area.

5.3 Parvozni boshqarish

Familiarize yourself with your remote controller's stick configurations for throttle, yaw, pitch, and roll. Practice in a safe, open environment before attempting complex maneuvers.

5.4 Kamera bilan ishlash

The O4 camera captures ultra-sharp 4K/120fps footage. Use your FPV goggles or connected mobile device to view the live feed and control camera settings. The advanced structural design isolates camera vibration for smooth footage.

5.5 Active Tracking

The drone supports active tracking features, allowing it to follow moving subjects. Refer to your remote controller and FPV system manual for specific active tracking mode activation and usage.

6. Xizmat va parvarish

6.1 Tozalash

Regularly clean the drone, especially after flights in dusty or dirty environments. Use a soft, dry cloth to wipe down the frame and propellers. Ensure the camera lens is clean for clear footage.

6.2 Parvona almashtirish

Inspect propellers before each flight for cracks, bends, or chips. Replace damaged propellers immediately using the spare HQprop DT76mmx3 V2 pairs and the provided screwdriver. Incorrectly installed or damaged propellers can affect flight stability and safety.

6.3 Mikrodasturlarni yangilash

Periodically check the GEPRC official website for firmware updates for the TAKER F722 45A 32Bit AIO flight system (FC Firmware: GEPRC_F722_AIO). Follow the provided instructions carefully to ensure proper update installation.

6.4 Batareyani parvarish qilish

Store LiHV batteries in a cool, dry place away from direct sunlight. Do not overcharge or over-discharge batteries. Always use a compatible charger. Discontinue use of any damaged or swollen batteries.

7. Muammolarni bartaraf qilish; nosozliklarni TUZATISH

  • Dron yoqilmayapti: Ensure the battery is fully charged and correctly connected to the XT30 connector.
  • No FPV feed: Check the connection between the O4 Air Unit Pro and your FPV goggles. Ensure both devices are powered on and correctly paired.
  • Beqaror parvoz: Inspect propellers for damage or incorrect installation. Calibrate the gyroscope and accelerometer if necessary (refer to the flight controller manual).
  • Masofadan boshqarish pulti ulanmayapti: Ensure the remote controller is powered on and correctly bound to the drone's receiver (PNP digital built-in VTS receiver). Use the frequency pairing ejector pin if re-binding is required.

For further assistance, please contact GEPRC customer support.

8. Texnik shartlar

XususiyatSpetsifikatsiya
ModelCinelog30 V3 O4 Pro Quadcopter
Ramka modeliGEP-CL30 V3
Carbon Fiber Plate Thickness2.5 mm
G'ildirak bazasi128 mm
Parvoz tizimiTAKER F722 45A 32Bit AIO
MCUSTM32F722RET6
GiroICM 42688-P
FC proshivkaGEPRC_F722_AIO
Flash16MB
ESC32Bit 45A
DvigatelSPEEDX2 1404 3850KV
ParvonalarHQprop DT76mmx3 V2
Batareya ulagichiXT30
VTXO4 AIR Unit Pro
KameraO4
AntennaO4 original
Qabul qiluvchiPNP (digital built-in VTS receiver)
Tavsiya etilgan batareyaLiHV 4S 660mAh-720mAh
Approximate Flight Time8’10″ (Tested at slow cruising speeds; actual times may vary with flying method)
Video suratga olish ruxsati4K
Element og'irligi190 gramm (taxminan 6.7 untsiya)
Mahsulot o'lchamlari7.99"L x 7.99"W x 3.54"Y

9. Kafolat va qo'llab-quvvatlash

For warranty information, technical support, or to purchase replacement parts, please visit the official GEPRC websayti yoki bevosita mijozlarga xizmat ko'rsatish bilan bog'laning. Kafolat da'volari uchun xarid kvitansiyasini saqlang.

ga ham tashrif buyurishingiz mumkin GEPRC Store on Amazon qo'shimcha mahsulot haqida ma'lumot va qo'llab-quvvatlash resurslari uchun.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.