O'rnatish diagrammasi

Lampochkani o'rnatish yoki almashtirishdan oldin, tozalash yoki boshqa texnik xizmat ko'rsatishdan oldin har doim quvvatni uzing.

1. Armaturani asl paketidan olib tashlang.
2. Separate mounting plate (1c) from canopy removing canopy screws (2f)
3. Attach mounting plate (1c) to electrical junction box (la) using screws provided (1d) in hardware package
4. Armatura balandligini o'zgartirish uchun sim tutqichni (2g) bosib turing va simni kerakli uzunlikka suring va mahkamlash uchun sim tutqichni (2g) qo'yib yuboring (kerak bo'lsa, ortiqcha simni olib tashlang)
5. Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1e)
6. Tegishli elektr ulanishlarini (qoradan issiq “L”, oqdan neytralga “N”, tuproqdan “GND”ga) apparat paketida taqdim etilgan simli gaykalar (1b) bilan amalga oshiring.
7. Attach canopy(2a) to mounting plate(1c) with canopy screws(2f) and nuts(2c) , tighten them(2f and 2c).
8. Agar kerak bo'lsa, simli tutqichni (2g) bosib va ​​ushlab turing, so'ngra simni kerakli uzunlikka sozlang.

1. To shorten the cable-just push the cable up, cable will be locked Automatically.
2. To length the cable-lift up on the cable and push up on the lock while keep the lock depressed, lower the cable to the desired length, release the lock to set.

A: Durang

LED simsiz masofadan boshqarish pultidan foydalanish bo'yicha ko'rsatmalar

I. Key function of remote control

1. indikator chirog'i
2. Yoqish; ishga tushirish
3. yorqinlik +
4. sovuq nur
5. tsikl
6. O'chirib qo'yish
7. yorqinlik -
8. issiq nur
9. tungi yorug'lik

II. Key instructions

Yoqish: Qisqa vaqt lamp lighting, Electricity within 5 s, Long press for the code function, After power on 5 s, Long press has no effect

O'chirish: Qisqa vaqt lamp goes out, Electricity within 5s, Long press for clear code function, After power on 5 s, Long press has no effect;

Sovuq yorug'lik +:

1, Short on time, Turn the cold light fixture on one level, At the same time, the warm light lamp darkens one level, There are 15 levels of cold light from out to full light;
2, Long time, The luminaire is gradually lightened, At the same time, the warm light gradually darkens;

Issiq yorug'lik +:

1, Short on time, The warm light fixture should be one step brighter, When the cold light lamp bir darajani qoraytiradi, Tashqaridan to'liq yorug'likka qadar 15 darajali iliq yorug'lik mavjud;
2, Long time, The warm luminaire is gradually lightened, At the same time, the cold light gradually darkened;

brightness + :

1, Short on time, Heat and cold light lamps are brighter, There are 11 levels of brightness from lowest to highest;
2, Long time, Cold and warm light lamps and lanterns are gradually brightened;

brightness – :

1, Short on time, Dim the light and cold lamps, eng yuqoridan pastgacha yorqinlikning 11 darajasi mavjud;
2, Long time, The cold and warm light lamps are gradually dimmed; cycle: Short press the loop key, The light is Warm, neutral, cold, Nightlight, Four state cycles, Press short to change the state one at a time; night lamp: Tungi yorug'lik tugmasini qisqa bosing, al.ning eng past yorqinligiamp converted to Warm light;

The key light : Key indicator light, The indicator button is pressed;

Eslatma: Isitish va sovutish yorug'lik sozlamalaridan biri, iste'molchilar o'zlarini quvvat manbai va l bo'yicha belgilashlari mumkin.amps.

III. Functional specifications

Xaritalash funksiyasi

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 soniya. Long press the light button once, LED light flashes slowly once. The code successfully. Then the remote control can control the brightness, cooling and heating of the LED lights with good code.
Note: An LED light is only controlled by the last successful remote control, For example, If an LED 1 ight fixture, There is a new remote control and its code matching is successful, Then the remote control will automatically clear the code with the lamp. But a remote control can be coded and controlled with multiple LED lights,

Kodni tozalash funktsiyasi

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 soniya, Long press the Turn off button or nightlight button once, LED light slow flash 2 time, The Ming and Qing dynasties were successful.

Note: The function of code clearing is based on the code matching between the remote control and the lamp, Masalanample, quyidagi hollarda, masofadan boshqarish pulti va lamp do not have the function of code clearing, If there is no clear code function, A long press to turn off the light has no effect.
(1) The remote control is not coded with the lamp, Then there is no clear code function.
(2) When they had finished coding, they cleared the code, Then there is no clear code function.
(3) They have coded each other, But then came a new remote control that corresponded with the light fixture, Then the remote control and its code function will automatically clear, No clear code function.

1. On switch function,

Lamp is normally energized, Power on the 0.5S-2S switch, The light is Warm, neutral, cold, Nightlight, 4 state loop Twitches.

2. Xotira funktsiyasini o'chirish

LED chiroqlarining yorqinligini sozlash uchun masofadan boshqarish pultidan foydalaning, LED l yorqinliginiamps va masofadan boshqarish pultining kod qiymati 15S quvvatdan keyin LED kontroller xotirasida saqlanadi, quvvatni yo'qotganingizdan keyin quvvatni yoqing va l ni yoqing.amp at its previous brightness, And has the code remote control is still controllable.

Hujjatlar / manbalar

Digilog E27 LED simsiz masofadan boshqarish pulti [pdf] Oʻrnatish boʻyicha qoʻllanma E27 LED simsiz masofadan boshqarish pulti yoritgichi, E27, LED simsiz masofadan boshqarish pulti yoritgichi, masofadan boshqarish pulti yoritgichi, yorug'lik armaturasi, armatura

Ma'lumotnomalar

• Foydalanuvchi uchun qo'llanma