DIY Bluetooth 5.0 Karnay Musiqa Spektri LED Miltillovchi Quvvat Ampko'taruvchi to'plam

1. Kirish

This RGB LED Spectrum Bluetooth Audio Speaker DIY Kit provides an engaging electronic project for enthusiasts. It features a 10-piece RGB LED music spectrum display and supports audio playback via Bluetooth 5.0, TF Card, and U-disk. The kit includes 4ohm 2W speakers, delivering clear and loud sound. It is designed for manual soldering and offers simple operation with remote control capabilities.

Asosiy xususiyatlar:

• Music spectrum display with 10 RGB LEDs.
• Bluetooth 5.0 audio playback.
• Support for TF Card and U-disk music sources.
• Infrared remote control for convenient operation.
• Adjustable Next/Previous track, Volume (+/-), and Play/Pause functions.
• Power OFF memory function.
• Designed for DIY manual soldering practice.
• Simple and easy to operate.

2. Texnik shartlar

3. Komponentlar ro'yxati

To'plam quyidagi komponentlarni o'z ichiga oladi:

Eslatma: Users can complete the installation according to the PCB silk screen and component list. For a detailed PDF manual, please refer to: GY19298.pdf

Image: All components included in the DIY kit.

4. O'rnatish va yig'ish bo'yicha ko'rsatmalar

O'rnatish bo'yicha umumiy maslahatlar:

• **Tools Required:** Soldering iron (<50 Watt), rosin core solder, wire cutters, wire strippers, Philips screwdriver.
• Be patient throughout the installation process.
• Avoid prolonged contact of the soldering iron with components (max 1.0 second) to prevent damage.
• Pay close attention to component polarity (positive and negative).
• Strictly avoid short circuits.
• Avval murakkab komponentlarni o'rnating.
• Ensure all components are in the correct direction and place.
• Wear anti-static gloves or wristbands when handling electronic components.
• Install LEDs according to specified rules; incorrect installation will prevent them from lighting.
• It is strongly recommended to read the entire manual before starting assembly.

Detailed Assembly Steps:

1. **Step 1: Install 20Kohm Metal Film Resistors (R1, R3)**
   Install two 20Kohm metal film resistors at positions R1 and R3 on the PCB. Identify the resistor value by its color code.
2. **Step 2: Install 470ohm Metal Film Resistors (R4, R5)**
   Install two 470ohm metal film resistors at positions R4 and R5 on the PCB. Identify the resistor value by its color code.
3. **Step 3: Install 2Mohm Metal Film Resistor (R2)**
   Install one 2Mohm metal film resistor at position R2 on the PCB. Identify the resistor value by its color code.
   

   Image: PCB with various components, including resistors.

4. **Step 4: Install DIP-6 IC CD4017 (U1)**
   Locate the mark (notch) on one end of the IC and align it with the corresponding mark (curved silk screen printing) on the PCB at U1.
5. **Step 5: Identify LED Polarity**
   The leads of the LED must be installed correctly. Incorrect installation will prevent the LED from lighting. Here are methods to identify polarity:
   
   • **Length:** The longer pin is the positive (anode) lead; the shorter pin is the negative (cathode) lead.
   • **Internal Structure:** Look into the plastic case; the negative (cathode) side is typically thicker/bigger than the anode side.
   • **Flat Edge:** The negative (cathode) lead is the pin nearest to the flat edge on the plastic case.
   • **Test with 3V Battery/Multimeter:** Connect the LED to a 3V power supply (briefly, less than 0.5 seconds). The pin connected to the positive of the 3V supply that makes the LED light up is the positive (anode) lead.
   • **PCB Markings:** The white mark '+' on the PCB indicates the positive (anode) connection.
   

   Image: Diagram illustrating LED polarity identification methods.

6. **Step 6: Install 5mm RGB LEDs (D1-D10)**
   Install ten 5mm RGB LEDs at positions D1-D10. Pay attention to distinguishing between positive and negative leads as described in Step 5, and bend the LED pins as needed.
7. **Step 7: Install TO-92 S9014 Transistor (Q1)**
   Install one TO-92 S9014 transistor at Q1. Ensure the installation direction matches the arc screen printing on the PCB.
   

   Image: Transistor S9014 (Q1) installed on the PCB.

8. **Step 8: Install 9*7mm MIC Microphone (MK1)**
   Install one 9*7mm MIC microphone at MK1. Distinguish between positive and negative; the marked pin is the negative pole.
   

   Image: MIC Microphone (MK1) installed on the PCB.
9. **Step 9: Install 1uF Electrolytic Capacitor (C3)**
   Install one 1uF electrolytic capacitor at C3. The white '+' on the PCB silk screen printing indicates the positive (anode) connection. The longer lead of the capacitor is positive (anode).
   

   Image: Electrolytic Capacitor C3 installed on the PCB.

10. **Step 10: Install 5mm RGB LED (D11)**
    Install one 5mm RGB LED at D11, paying attention to its polarity as described in Step 5.
    

    Image: LED D11 installed on the PCB.

11. **Step 11: Install 100uF Electrolytic Capacitor (C2)**
    Install one 100uF electrolytic capacitor at C2. The white '+' on the PCB silk screen printing indicates the positive (anode) connection. The longer lead of the capacitor is positive (anode).
    

    Image: Electrolytic Capacitor C2 installed on the PCB.
12. **Step 12: Install Extra Pins from LED (J1-J3)**
    Install the extra pins from the LED at positions J1-J3 on the PCB.
13. **Step 13: Install 15cm 2Pin PH2.0 Wire for Power**
    Install one 15cm 2Pin PH2.0 wire. Connect the red wire to '+' and the black wire to '-'. Cut the white socket. These two wires will be used to connect power. Refer to the wiring location and note the PCB mark if the wire color differs.
    

    Image: Power wire connected to the PCB.

14. **Step 14: Tear off Protective Film from Acrylic Surface**
    Carefully remove the protective film from all acrylic panels.
    

    Image: Acrylic panels before assembly, with protective film.

15. **Step 15: Fix M3*8 Copper Pillars and M3*6mm Screws to Acrylic Base**
    Fix two M3*8 copper pillars and two M3*6mm screws onto the acrylic panel that serves as the base for the LED board.
    

    Image: Acrylic base with copper pillars installed.
16. **Step 16: Fix RGB LED Board on Copper Pillars**
    Fix the RGB LED board onto the copper pillars using two M3*6mm screws.
    

    Image: LED board mounted on copper pillars.

17. **Step 17: Understand Bluetooth Audio Controller Interface**
    Familiarize yourself with the functions of the Bluetooth audio controller's interface, including the infrared remote control receiver, TF card socket, U-disk socket, and LED indicator.
    

    Image: Front panel of the Bluetooth audio controller, showing various ports and indicators.

18. **Step 18: Bluetooth Audio Controller Wiring Diagram**
    Refer to the wiring diagram for the Bluetooth audio controller. The Bluetooth module comes in two versions (DIP Socket and SMD Socket) which are shipped randomly. Three connection methods are provided to connect the Bluetooth module to the LED light board.
    

    Image: Wiring diagram for the Bluetooth audio controller.
19. **Step 19: Fix Bluetooth Audio Controller to Acrylic Panel**
    Fix the Bluetooth audio controller onto the acrylic panel using two M3*10mm screws and two M3 nuts.
    

    Image: Bluetooth audio controller securely mounted on the acrylic panel.

20. **Step 20: Connect LED Board to Bluetooth Audio Controller (3 Methods)**
    
    • **Method 1 (DIP Socket Version):** Connect '5V' from the Bluetooth module to '+' on the LED board, and 'GND' from the Bluetooth module to '-' on the LED board.
      

      Image: Wiring for DIP Socket Version Bluetooth module.

    • **Method 2 (SMD Socket Version):** Connect 'GND' from the Bluetooth module to '-' on the LED board. Connect the pad marked '5V' on the right of the Bluetooth module to '5V' on the LED board.
      

      Image: Wiring for SMD Socket Version Bluetooth module.
    • **Method 3 (DIP and SMD Socket Version):** This method changes the power supply connection point of the LED light board. Refer to Step 26A for details if 5V/GND connections are not found.
21. **Step 21: Install 15cm 2Pin PH2.0 Wire to Speakers**
    Install two 15cm 2Pin PH2.0 wires to the two 4ohm 3W speakers. Speakers do not require polarity distinction.
    

    Image: Speaker with PH2.0 wires connected.

22. **Step 22: Fix Speakers to Acrylic Panels**
    Fix the speakers onto the two smaller acrylic panels using eight M3*10mm screws and eight M3 nuts.
23. **Step 23: Fix DC-022 Power Socket**
    Fix one DC-022 power socket to the acrylic panel using its largest nut.
    

    Image: DC-022 Power Socket installed on the acrylic panel.
24. **Step 24: Fix Black Switch**
    Fix one black switch to the acrylic panel. Ensure the buckle on the switch is properly engaged for self-fixing. Pay attention to the installation direction.
    

    Image: Black Switch installed on the acrylic panel.

25. **Step 25: Wire DC-022 Power Socket and Black Switch**
    Cut approximately 3cm of red wire to connect the DC-022 power socket and the black switch. Ensure correct pin selection and avoid connecting to other pins.
    

    Image: Internal wiring connecting the power socket and switch.

26. **Step 26: Connect 15cm 2Pin PH2.0 Wire to DC-022 and Switch**
    Connect one 15cm 2Pin PH2.0 wire. The red wire connects to the black switch, and the black wire connects to the DC-022 power socket. Refer to the wiring location shown if the wire color differs.
27. **Step 26A: Connect LED Spectrum Board to Bluetooth Audio Controller (Alternative Method)**
    If the LED board receives voltage from the power socket and switch but not from the Bluetooth module, follow these steps (otherwise, ignore if using Method 1 or 2 from Step 20):
    
    • '5V' on the LED board connects to the middle pin on the switch (which has a red wire connected).
    • 'GND' on the LED board connects to the top pin on the DC-022 power socket (which has a black wire connected).

    This connection method is applicable for both DIP and SMD Socket versions of Bluetooth modules.

    

    Image: Wiring connections between the LED board, switch, and power socket.

28. **Step 27: Connect Power Wire and Speaker Wires**
    Connect one power wire to the red socket and the two speaker wires to the white sockets.
    

    Image: All internal wiring connections completed.
29. **Step 28: Assemble Acrylic Panels**
    Assemble the six acrylic panels using twelve M2*10mm screws and twelve M2 nuts. Be patient when installing the screws.
    

    Image: The assembled acrylic casinkarnayning g.

30. **Step 29: Connect to Power Supply**
    Connect the assembled unit to a power supply and enjoy the effect. Ensure sufficient working current; a 5V 2A power supply is recommended. Exercise care and provide additional support to the acrylic with one hand while pressing the switch into place with the other hand when the power is plugged in.
    

    Image: The final assembled speaker unit, ready for use.

5. Foydalanish bo'yicha ko'rsatmalar

Bluetooth ulanishi:

1. Turn on the Bluetooth function on your mobile phone or other device.
2. Ni qidirish the device named "DW-CT10-BT".
3. Select "DW-CT10-BT" to connect. Once connected, the speaker is ready for audio playback.
4. If Bluetooth is disconnected, the speaker will automatically switch to TF card or U-disk mode if media is present.

Masofadan boshqarish funksiyalari:

Image: Remote control layout and corresponding speaker button functions.

• **ON/OFF:** Power on or off the speaker.
• **Mode:** Switch between music sources (Bluetooth / U-disk / TF Card).
• **Mute:** Mute or unmute the audio.
• **Prev/V-:** Short press to select the previous music track. Long press to decrease volume.
• **Next/V+:** Short press to select the next music track. Long press to increase volume.
• **Play/Pause:** Play or pause music playback.
• **EQ:** Switch sound quality modes.
• **RPT:** Repeat function.
• **U/SD:** Switch between U-disk and TF card.
• **Number Buttons (0-9):** No function, please do not use them.

6. Xizmat ko'rsatish

• Keep the device clean and dry. Avoid exposure to moisture or extreme temperatures.
• Do not use harsh chemicals or abrasive cleaners on the acrylic shell or electronic components. Use a soft, dry cloth for cleaning.
• Ensure all connections remain secure. Periodically check for loose wires or components.
• If the device is not in use for an extended period, disconnect it from the power supply.

7. Muammolarni bartaraf qilish; nosozliklarni TUZATISH

• **Quvvat yo'q:**
  - Ensure the power supply is connected correctly and provides DC 3.7V-5V.
  - Check the black switch for proper installation and function.
  - Verify all power wiring (Step 13, 25, 26, 26A) is correct and free of short circuits.
• **LEDs Not Lighting/Incorrectly:**
  - Recheck LED polarity during installation (Step 5). Incorrect polarity will prevent LEDs from lighting.
  - Ensure all LEDs are installed according to the specified rules.
  - Verify soldering points for LEDs are solid and free of cold joints.
• **No Sound/Poor Sound Quality:**
  - Check speaker wiring (Step 21) for secure connections.
  - Ensure the Bluetooth module is correctly wired to the LED board (Step 20).
  - Verify the music source (Bluetooth, TF Card, U-disk) is properly selected using the 'Mode' button or remote.
  - Confirm the volume is not set to minimum or muted.
  - Ensure the power supply provides sufficient current (recommended 5V 2A for optimal sound).
• **Bluetooth Connection Issues:**
  - Make sure the speaker is powered on and in Bluetooth mode.
  - Ensure your device's Bluetooth is enabled and searching for "DW-CT10-BT".
  - Try restarting both the speaker and your Bluetooth device.
• **Remote Control Not Working:**
  - Check if the remote control's battery needs replacement.
  - Ensure there are no obstructions between the remote and the speaker's infrared receiver.
• **Components Damaged During Soldering:**
  - Avoid prolonged contact of the soldering iron with components (max 1.0 second). Excessive heat can damage components.

8. Foydalanuvchi maslahatlari

• **Power Supply:** For the best sound quality and stable operation, use a 5V power supply with a current output of 2A or higher. The device is not rechargeable; it requires a constant 5V power input.
• **Soldering Practice:** This kit is excellent for practicing soldering skills. Take your time with each joint to ensure strong, clean connections.
• **Component Identification:** Double-check component values and polarities before soldering to avoid errors.
• **Acrylic Assembly:** When assembling the acrylic casing, handle the panels carefully to avoid scratches. Provide additional support to the acrylic with one hand while pressing the switch into place with the other hand when the power is plugged in.

9. Kafolat va qo'llab-quvvatlash

This product is a DIY kit, and its functionality depends on proper assembly. Please ensure all instructions are followed carefully. For any technical assistance or inquiries, please contact the seller directly. A detailed PDF user manual is available at: GY19298.pdf