SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. Kirish

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

1.1-rasm: Old view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. Xavfsizlik ma'lumotlari

• O'rnatish va ishlatishdan oldin barcha ko'rsatmalarni diqqat bilan o'qing.
• Elektr ta'minoti voltage qurilma talablariga mos keladi (85-265V AC, 50/60Hz).
• All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
• Qurilmani haddan tashqari namlik, chang yoki korroziy gazlar bo'lgan muhitda ishlatmang.
• Har qanday texnik xizmat ko'rsatish yoki simlarni o'zgartirishdan oldin elektrni uzing.
• Keep the device away from strong electromagnetic interference.

3. Mahsulot xususiyatlari

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Wide operating temperature range.
• Compact and easy-to-install design.

4. Paket tarkibi

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• 1 x foydalanuvchi qo'llanmasi (ushbu hujjat)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. Sozlash

5.1 O'rnatish

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2 Bolalar

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Terminals 1 & 2: AC Power Supply (85-265V AC, 50/60Hz)
• Terminals 3 & 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Terminals 6 & 7: Alarm Output (ALM) - Relay contacts for alarm.
• Terminals 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Terminals 11 & 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. Foydalanish bo'yicha ko'rsatmalar

6.1 Ko'rsatishview

The meter features a dual display:

• PV (jarayon qiymati): The upper red display shows the current measured temperature/humidity.
• SV (Qiymatni o'rnatish): The lower green display shows the desired set point.
• OUT ko'rsatkichi: Illuminates when the main output is active.
• AT ko'rsatkichi: Illuminates when the auto-tuning function is active.
• AL1/AL2 Indicators: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 Tugma funksiyalari

• SET tugmasi: Parametrlarni sozlash rejimiga kirish va tanlovlarni tasdiqlash uchun ishlatiladi.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (Down) Button: Decreases the value of a parameter or set point.
• ▲ (Up) Button: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. In normal operating mode, press the SET button once. The SV display will begin to flash.
2. dan foydalaning ▲ (Yuqoriga) va ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. ni bosing SET button again to confirm the new SV and exit the setting mode.

6.4 Advanced Parameter Settings

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the SET button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (Yuqoriga) va ▼ (Down) buttons to navigate through parameters and the SET button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7. Xizmat ko'rsatish

• Tozalash: Displeyni arting va casinyumshoq, quruq mato bilan arting. Abraziv tozalagichlar yoki erituvchilardan foydalanmang.
• Tekshirish: Vaqti-vaqti bilan simli ulanishlarni bo'shashmaslik yoki korroziya uchun tekshiring.
• Saqlash: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

8. Muammolarni bartaraf qilish; nosozliklarni TUZATISH

9. Texnik shartlar

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. Kafolat va qo'llab-quvvatlash

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER webaloqa ma'lumotlari uchun sayt.