eSkde CS58-S7 benzinli arra foydalanuvchi qo'llanmasi

1. Kirish

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your eSkde CS58-S7 Petrol Chainsaw. Please read this manual thoroughly before operating the chainsaw to ensure proper use and to prevent injury or damage.

2. Xavfsizlik ma'lumotlari

Operating a chainsaw can be hazardous. Adhere to all safety warnings and instructions to minimize risks.

2.1 Shaxsiy himoya vositalari (PPE)

• Bosh himoyasi: Xavfsiz dubulg'a kiying.
• Ko'zni himoya qilish: Use safety glasses or a face shield.
• Eshitish himoyasi: Wear ear defenders or earplugs.
• Qo'lni himoya qilish: Og'ir ish uchun qo'lqop kiying.
• Oyoq himoyasi: Zanjirli arra himoya qiluvchi shim yoki shlyapa kiying.
• Oyoq himoyasi: Wear steel-toed safety boots with good grip.

2.2 Umumiy xavfsizlik choralari

• Always inspect the chainsaw before each use for loose parts, damage, or fuel leaks.
• Ensure the chain brake is functional and engaged when starting or moving the saw.
• Ikki qo'lingiz bilan zanjirli arra tutqichlarini qattiq ushlab turing.
• Keep the work area clear of bystanders, children, and pets.
• Be aware of kickback potential and use proper cutting techniques to avoid it.
• Handle fuel with extreme care. Mix and refuel in a well-ventilated area away from ignition sources.
• Do not operate the chainsaw when fatigued or under the influence of alcohol or medication.
• Store the chainsaw safely when not in use, with the bar cover in place.

3. Mahsulot komponentlari

Familiarize yourself with the main components of your eSkde CS58-S7 Petrol Chainsaw.

3.1 Qo'shimcha aksessuarlar

• 20" Guide Bar
• 2 x zanjirlar
• Asboblar to'plami
• Yoqilg'i aralashtirish shishasi
• Saqlash sumkasi
• Bar qopqog'i

4. O'rnatish va yig'ish

4.1 Bar and Chain Assembly

1. Dvigatel o'chirilganligiga va zanjir tormozi uzilganligiga ishonch hosil qiling.
2. Remove the side cover nuts and the side cover.
3. Place the guide bar onto the studs, ensuring the chain tensioner pin aligns with the hole in the bar.
4. Carefully fit the chain around the sprocket and into the groove of the guide bar. Ensure the cutting edges of the chain are facing the correct direction (refer to chain direction indicator on the bar).
5. Yon qopqoqni joyiga qo'ying va yong'oqlarni qo'l bilan mahkamlang. Hali to'liq tortmang.
6. Adjust chain tension (see Section 5.2).

4.2 Fuel and Oil Preparation

The eSkde CS58-S7 uses a 2-stroke engine and requires a specific fuel mixture.

• Yoqilg'i aralashmasi: Mix unleaded petrol with high-quality 2-stroke engine oil at a ratio of 25:1 (Petrol:Oil). Use the provided fuel mixing bottle for accurate measurement.
• Yoqilg'i quvvati: The fuel tank capacity is 550ml.
• Zanjir yog'i: Fill the chain oil tank with good quality chain lubricant. The chain oil tank capacity is 260ml. This oil automatically lubricates the chain and bar during operation.

Muhim: Never use pure petrol in the chainsaw. Incorrect fuel mixture will cause severe engine damage and void the warranty.

5. Foydalanish bo'yicha ko'rsatmalar

5.1 Zanjirli arrani ishga tushirish

Cold Start Procedure:

1. Zanjirli arra qattiq, tekis yuzaga qo'ying.
2. Engage the chain brake by pushing the front hand guard forward.
3. Pull out the choke knob fully.
4. Press the primer bulb several times until fuel is visible in the return line.
5. Pull the starter cord firmly and steadily until the engine fires briefly (usually 1-3 pulls).
6. Push the choke knob halfway in.
7. Pull the starter cord again until the engine starts and runs.
8. Allow the engine to warm up for a few seconds, then disengage the chain brake by pulling the front hand guard back.

Warm Start Procedure:

1. Zanjir tormozini yoqing.
2. Pull the starter cord firmly and steadily until the engine starts. No choke or priming is usually needed.
3. Disengage the chain brake once the engine is running smoothly.

5.2 Chain Tension Adjustment

Correct chain tension is crucial for safe and efficient operation. The chain should be snug against the guide bar, but still able to be pulled around by hand with light effort.

1. Loosen the side cover nuts slightly.
2. Use the tensioning screw (usually located on the side cover or near the bar studs) to adjust the chain tension. Turn clockwise to tighten, counter-clockwise to loosen.
3. Once tension is correct, fully tighten the side cover nuts.
4. Check tension again after a few cuts, as new chains can stretch.

5.3 Kesish texnikasi

Always maintain a stable footing and a firm grip on the chainsaw. Plan your cuts to avoid pinching the bar or chain.

• Kesish: For felling trees, ensure the area is clear and plan the felling direction. Make a notch cut on the felling side, then a felling cut from the opposite side.
• Limbing: Remove branches from a felled tree. Work from the base towards the top, supporting the branch if necessary to prevent pinching.
• Buking: Cutting a felled log into shorter sections. Use a sawhorse or elevate the log to avoid cutting into the ground.

6. Xizmat ko'rsatish

Muntazam texnik xizmat ko'rsatish zanjirli arra uzoq umr va xavfsiz ishlashini ta'minlaydi.

6.1 Kundalik texnik xizmat ko'rsatish

• Zanjirning kuchlanishini tekshiring.
• Check chain sharpness. Sharpen or replace as needed.
• Havo filtrini tozalang.
• Check the oil level in the chain oil tank.
• Inspect the guide bar for wear or burrs.
• Clean debris from the chain brake mechanism.

6.2 Davriy texnik xizmat ko'rsatish

• Buji: Uchqun shamchasini muntazam tekshirib turing va tozalang. Agar eskirgan yoki ifloslangan bo'lsa, uni almashtiring.
• Yoqilg'i filtri: Check and clean or replace the fuel filter periodically.
• Carburettor Adjustment: If the engine runs poorly, the carburettor may need adjustment. This should ideally be done by a qualified technician.
• Umumiy tozalash: Keep the engine cooling fins and air intake clean to prevent overheating.

7. Muammolarni bartaraf qilish; nosozliklarni TUZATISH

Ushbu bo'lim zanjirli arra bilan duch kelishi mumkin bo'lgan umumiy muammolarni ko'rib chiqadi.

8. Texnik shartlar

9. Kafolat va qo'llab-quvvatlash

For warranty information, please refer to the documentation provided with your purchase or contact eSkde customer support. Keep your proof of purchase for any warranty claims.

For technical assistance or spare parts, please contact your retailer or the eSkde customer service department. Provide your model number (CS58-S7) and purchase date when seeking support.