SoliTek SOLID Series Solar Modules Installation Guide

SoliTek SOLID Series Solar Modules

Foydalanish bo'yicha ko'rsatmalar

• Read this guide entirely before installation.
• This document provides minimum requirements and recommendations for safe and successful installation of SoliTek PV modules and is necessary to retain compliance with IEC 61215, IEC 61730, and UL 61730 standards.
• This guide provides basic information on JSC SoliTek Cells SOLID series photovoltaic modules, including their installation and safe handling.
• All instructions should be read and understood before attempting installation. Contact your dealer or JSC SoliTek Cells for further information if needed.
• This documentation refers to the PV modules themselves and is not a comprehensive installation manual for personnel not specifically trained in PV modules.
• It serves as a general but strictly mandatory reference for the installer. Infringement or inaccurate observance of any clause in this documentation voids the warranty.
• The installer must understand and follow all applicable local, state, and federal regulations and standards for building construction, electrical design, fire, and safety.
• Check with local authorities for permitting requirements before installing or maintaining PV modules, and become familiar with mechanical and electrical requirements for photovoltaic systems.
• Ushbu qo'llanmadagi ko'rsatmalarga rioya qilmaslik tizim komponentlariga zarar etkazishi, xodimlarni xavf ostiga qo'yishi, mulkka zarar etkazishi yoki panel kafolatini bekor qilishi mumkin.
• Rooftop PV systems should only be installed on dwellings formally analyzed for structural integrity and confirmed to be capable of handling the additional weighted load of PV system components (including PV modules) by a certified building specialist or engineer.

UMUMIY TALABLAR

• Iltimos, o'rnatishdan oldin ushbu qo'llanmani to'liq o'qing.
• Ushbu hujjatning maqsadi SoliTek PV modullarini xavfsiz va muvaffaqiyatli o'rnatish uchun minimal talablar va tavsiyalarni berishdir.
• Ushbu hujjat, shuningdek, SoliTek PV modulining IEC 61215, IEC 61730, UL 61730 standartlariga muvofiqligini saqlab qolish uchun zarur bo'lgan talablarni o'z ichiga oladi.
• Ushbu qo'llanmada "SoliTek Cells" OAJ SOLID seriyali fotovoltaik modullar, ularni o'rnatish va xavfsiz ishlash bo'yicha asosiy ma'lumotlar mavjud. O'rnatishdan oldin barcha ko'rsatmalarni o'qib chiqish va tushunish kerak. Savollaringiz bo'lsa, qo'shimcha ma'lumot olish uchun dileringiz yoki "SoliTek Cells" OAJ bilan bog'laning.
• This documentation refers to the PV-modules themselves and is not meant to be a complete installation manual for personnel not specifically trained to PV-modules.
• It serves as a general but strictly mandatory reference for the Installer.
• Ushbu hujjatning biron bir bandini buzish yoki noto'g'ri bajarish kafolatni bekor qiladi.
• O'rnatuvchi bino qurilishi, elektr dizayni, yong'in va xavfsizlik bo'yicha barcha tegishli mahalliy, shtat va federal qoidalar va standartlarni tushunishi va ularga rioya qilishi kerak va PV modullarini o'rnatish yoki saqlashga urinishdan oldin tegishli ruxsat berish talablarini aniqlash uchun mahalliy hokimiyat organlari bilan tekshirishi kerak. fotovoltaik tizimlar uchun mexanik va elektr talablari bilan tanishish.
• Ushbu qo'llanmadagi ko'rsatmalarga rioya qilmaslik tizim komponentlariga zarar etkazishi, xodimlarni xavf ostiga qo'yishi, mulkka zarar etkazishi yoki panel kafolatini bekor qilishi mumkin.
• Uyingizda PV tizimlari faqat strukturaviy yaxlitligi uchun rasmiy ravishda tahlil qilingan va sertifikatlangan qurilish mutaxassisi yoki muhandis tomonidan PV tizimi komponentlarining, shu jumladan PV modullarining qo'shimcha og'irlikdagi yukini ko'tarishga qodir ekanligi tasdiqlangan turar-joylarga o'rnatilishi kerak.
• For your safety, do not attempt to work on a rooftop until safety precautions have been identified and taken, including, without limitation fall protection measures, ladders or stairways, and personal protective equipment (PPE).
• For your safety, do not install or handle PV modules under adverse conditions, including, without limitation strong or gusty winds, and wet or frosted roof surfaces.
• Yassi plitali PV modul konstruktsiyasi ikkita shisha choyshab ichida izolyatsion material ichiga o'ralgan quyosh batareyalarining laminatlangan yig'ilishidan iborat.
• Kelajakda foydalanish uchun ushbu hujjatni xavfsiz joyda saqlang.
• Modulni qismlarga ajratishga urinmang va biriktirilgan etiketkalar yoki komponentlarni olib tashlamang! Bu kafolatni bekor qiladi.

Ishlov berish va qo'llash

QO'LLANISH

• SoliTek PV modules must be transported in the supplied packaging only and kept in the packaging until they are ready to be installed.
• Protect pallets against movement and exposure to damage during transportation. Secure pallets from falling over.
• Palet o'ramida ko'rsatilganidek, qo'yiladigan tagliklarning maksimal balandligidan oshmang.
• Store pallets in a cool and dry location until the PV modules are ready to be unpackaged.
• SoliTek PV modules are heavy and should be handled with care. Never use the junction box or cables as a grip.
• Do not exert mechanical stress on the cables.
• Never step on PV modules or drop or place heavy objects on them.
• Be careful when placing PV modules on hard surfaces and secure them from falling.
• Broken glass can result in personal injury. PV modules with broken glass cannot be repaired and must not be used.
• Broken or damaged PV modules must be handled carefully and disposed of properly.

ILOVA

Cheklovlar

• SoliTek PV modules must be mounted on appropriate mounting structures positioned on suitable buildings, the ground, or other structures suitable for PV modules (e.g. carports, building facades or PV trackers).
• PV modules must not be mounted on moving vehicles of any kind. Modules must not be installed in locations where they could be submerged in water.
• Do not install modules above 2000 m (6561 ft) altitude above sea level
• Sun'iy konsentratsiyalangan yorug'lik SoliTek PV modullariga yo'naltirilmasligi kerak.

Tavsiyalar

• SoliTek yomg'irdan to'g'ri o'z-o'zini tozalash imkonini berish uchun PV modullarini kamida 10 daraja egilish burchagida o'rnatishni tavsiya qiladi.
• PV moduli yoki modullarining qisman yoki to'liq soyalanishi tizim ish faoliyatini sezilarli darajada kamaytirishi mumkin.
• SoliTek PV modullari tomonidan ishlab chiqarilgan energiya miqdorini oshirish uchun yil davomida soya miqdorini minimallashtirishni tavsiya qiladi.
• Yuqori tizim jildtages could be induced in the event of an indirect lightning strike, which could cause damage to PV system components.
• The open area of wire loops should be minimized in order to reduce the risk of lightning-induced voltage ko'tariladi.
• Yaxshiroq modul shamollatish va qisqaroq ulanish kabellari elektr energiyasini ishlab chiqarishni oshiradi.

Ikki yuzli modullar uchun:

• Modul ostidan ko'proq yorug'lik o'tishi va keyin aks etishi uchun PV paneli balandligini erdan oshirish tavsiya etiladi
• Modullar oq (yuqori albedo qiymati), yorug'likni aks ettiruvchi yuzalar ustida o'rnatilsa, ikki yuzli daromad sezilarli darajada oshadi.

Elektr o'rnatish

XAVFSIZLIK

• PV modullari oqim va voltage har qanday intensivlikdagi yorug'lik ta'sirida. Elektr toki yuqori yorug'lik intensivligi bilan ortadi. DC jildtage 50 volt yoki undan yuqori kuchlanish potentsial o'limga olib keladi. Yorug'lik ostida ishlaydigan PV tizimining jonli sxemasiga ulanish halokatli elektr toki urishiga olib kelishi mumkin.
• PV modullarini yorug'likdan butunlay olib tashlash yoki ularning old yuzasini shaffof bo'lmagan material bilan qoplash orqali ularni quvvatsizlang. Har qanday yorug'lik ta'sirida bo'lgan modullar bilan ishlashda kuchlanishli elektr jihozlarining xavfsizlik qoidalariga kelsak. PV modullari bilan ishlashda izolyatsiyalangan asboblardan foydalaning va metall zargarlik buyumlarini taqmang.
• Yoy va elektr toki urishining oldini olish uchun yuk ostida elektr aloqalarini uzmang. Noto'g'ri ulanishlar, shuningdek, kamon va elektr toki urishiga olib kelishi mumkin. Ulagichlarni quruq va toza tuting va ularning ish holatida ekanligiga ishonch hosil qiling. Hech qachon metall buyumlarni ulagichlarga joylashtirmang yoki elektr aloqasini mustahkamlash uchun ularni hech qanday tarzda o'zgartirmang.
• Do not touch or handle PV modules with broken glass unless the PV modules are first disconnected, and you are wearing proper PPE. Avoid handling PV modules when they are wet unless cleaning the PV modules as directed in this manual. Never touch electrical and wet connections without protecting yourself with insulated gloves.
• The modules are qualified for Class II protection against electrical shock, in accordance with clause 4 of IEC 61730-1:2016, which can be used in systems operating at > 50 V DC or >240 W, where general contact access is anticipated and modules qualified for safety through UL 61730 within this application class are considered to meet the requirements of Safety Class II.
• Quyosh fotovoltaik tizimlarini o'rnatish maxsus ko'nikmalar va bilimlarni talab qiladi. Buni faqat malakali va maxsus yo'riqnomaga ega xodimlar bajarishi kerak. O'rnatuvchi barcha shikastlanish xavfini, shu jumladan elektr toki urishi xavfini o'z zimmasiga oladi.
• Faqat fotovoltaik tizimda foydalanish uchun maxsus mo'ljallangan uskunalar, ulagichlar, simlar va o'rnatish moslamalaridan foydalaning.
• Before any manipulation at an installed PV plant, switch it off first on the AC-side, and then on the DC side of the inverter or the charge controller.
• Yorug'likka ta'sir qiladigan fotovoltaik modulga ulangan simlarni uzganda, elektr yoyi paydo bo'lishi mumkin. Yoylar kuyishga olib kelishi, yong'inni boshlashi yoki boshqa yo'l bilan xavfsizlik (o'limga olib keladigan elektr toki urishi) muammolarini keltirib chiqarishi mumkin.
• Qolgan jildni tekshiringtage before starting and observe the local safety-relevant regulations for such working conditions.
• Oddiy sharoitlarda fotovoltaik modul ko'proq oqim va/yoki volt ishlab chiqarishi mumkintage (bu erda: 30V DC) standart sinov sharoitlarida bildirilganidan.
• DC vol. bilan aloqatage 30 V yoki undan yuqori kuchlanish potentsial xavfli hisoblanadi. Quyosh nurlari ta'sirida bo'lgan modullarni ulash yoki ishlatishda ehtiyot bo'ling.
• Faqat bir xil nominal chiqish oqimiga ega modullarni ketma-ket ulang. Agar modullar ketma-ket ulangan bo'lsa, umumiy hajmtage - individual modul volining yig'indisiga tengtages.
• Faqat bir xil hajmdagi modullarni yoki modullarning ketma-ket birikmalarini ulangtage in parallel. If modules are connected in parallel, the total current is equal to the sum of the individual module or series combination currents.
• Har doim ma'lum bir fotoelektr tizimida bir xil turdagi moduldan foydalaning.
• If the sum of short circuit currents of the parallel-connected modules exceeds the reverse current, string diodes or fuses have to be used in each string of modules connected in parallel. These string diodes or fuses have to be qualified for the maximum expected current and voltage. The fuse rating value is also corresponds to the maximum reverse current that a module can withstand. The reverse current value can be found on the product label, in the product datasheet or in chapter 8 of the installation manual. Observe the instructions and safety precautions for all other components used in the system, including wiring and cables, connectors, DC-breakers, inverters, etc.
• Elektr qurilmalarida foydalanish uchun ruxsat etilgan tegishli xavfsizlik vositalaridan (izolyatsiya qilingan asboblar, dielektrik qo'lqoplar, poyabzal va boshqalar) foydalaning.

CONFIGUURATION

• Oddiy sharoitlarda fotovoltaik modul ko'proq oqim va/yoki volt hosil qiladigan sharoitlarni boshdan kechirishi mumkintage than reported at Standard Test Conditions (STC: 1000 W/ m2, AM 1.5, and 250C/770F cell temperature) or Bifacial nominal power index(BNPl front irradiance 1000 W/m2, back irradiance 135 W/m2 AM 1.5, and 25 OC/770F cell temperature). The short-circuit current (ISC) should be multiplied by a factor of 1.25 and the open-circuit voltagE (VOC) komponent hajmini aniqlashda o'rnatish joyi uchun qayd etilgan eng past va eng yuqori muhit harorati asosida 1.25 koeffitsientga ko'paytirilishi kerak.tage ko'rsatkichlari, o'tkazgichning oqim ko'rsatkichlari, sug'urta o'lchamlari va PV chiqishiga ulangan boshqaruv elementlarining o'lchami.
• jildtagPV modullari to'g'ridan-to'g'ri ketma-ket ulanganda qo'shimcha hisoblanadi va PV modullari to'g'ridan-to'g'ri parallel ulanganda modul oqimlari qo'shimcha hisoblanadi. Turli xil elektr xususiyatlariga ega PV modullari to'g'ridan-to'g'ri ketma-ket ulanmasligi kerak. PV modullariga ulangan mos keladigan uchinchi tomon elektron qurilmalaridan foydalanish turli xil elektr ulanishlarini amalga oshirishi mumkin va ular ishlab chiqaruvchining ko'rsatmalariga muvofiq o'rnatilishi kerak.
• Maksimal hajmtage of serial interconnection of the modules must be less than the maximum certified module’s system voltage. Bundan tashqari, maksimal kirish hajmitaginverter va tizimdagi boshqa elektr qurilmalarning e ni hisobga olish kerak. Ochiq elektron jildtage of the array string needs to be calculated at the lowest expected a mbient temperature forthe location. The maximal system voltage for the module is indicated in the module’s datasheet.
• Accordingly, for BLACKSTAR, SOLID or MAGNUS series modules, the values of ISC and VOC under STC or BNPI marked on this module should be multiplied by a factor of 1,25 when determining component voltage ratings, conductor current ratings, fuse sizes, and size of controls connected to the PV output. In the USA, referto Section 690-8 of the National Electrical Code (N EC) for an additional multiplying factor of 125 percent (80 percent de-rating) which may be applicable.

Haddan tashqari oqimdan himoya qilish qurilmasi (OCPD)

• When the potential reverse current of a PV string exceeds the rated SoliTek PV module series fuse rating (values indicated at the module datasheet) an overcurrent protection device (OCPD) must be used.
• An overcurrent protection device is required for each series string if more than two series are connected in parallel.
• In this case, it is needed to use one fuse per string rated at 1.25 x Isc or higher (Isc is the PV module’s short circuit current at STC). A PV fuse on each PV string will protect the PV modules and conductors from overcurrent faults and help minimize any safety hazards.
• The PV fuse will also isolate the faulted PV string so the balance of the PV system can continue to generate electricity.
• Sug'urta amp reyting ≥ 1.25 x Isc
• Mavjud PV Sigortalar katalogida keyingi yuqori standart reytingni tanlang.
• Isc = Standart sinov shartlarida (STC) bitta modulning qisqa tutashuv oqimi.
• SoliTek modullarining Isc qiymatlarini hisobga olgan holda, o'rnatishda ishlatiladigan PV sigortalarining to'g'ri qiymati 30 A ni tashkil qiladi. SoliTek PV sigortalarini ham ijobiy, ham salbiy o'tkazgichlarda ishlatishni tavsiya qiladi.

KAbel va sim

SoliTek PV modullari ikkita standart, quyosh nuriga chidamli chiqish kabellari bilan ta'minlangan, ular ko'pchilik o'rnatish uchun tayyor PV konnektorlari bilan tugaydi. Ijobiy (+) terminalda erkak ulagich, salbiy (-) terminalda esa ayol ulagich mavjud. Modul simlari ketma-ket ulanishlar uchun mo'ljallangan (ya'ni, erkak (+) dan ayol (-) o'zaro bog'liqliklari), lekin ishlab chiqaruvchining ko'rsatmalariga rioya qilingan holda muqobil sim konfiguratsiyasiga ega bo'lishi mumkin bo'lgan mos keladigan uchinchi tomon elektr qurilmalarini ulash uchun ham ishlatilishi mumkin.
PV modulining maksimal qisqa tutashuv oqimida foydalanish uchun ruxsat etilgan tegishli kesma maydonlari bo'lgan dala simlaridan foydalaning. Barcha simlar kamida 1,8 kV kuchlanishli (1500 V voltdan yuqori) ikki tomonlama izolyatsiyalangan, o'zaro bog'langan kabellar bo'lishi kerak.tage) va minimal nominal harorat 90 ˚C (190 ° F). Sim o'lchami kamida 4 mm² (12 AWG). Izolyatsiya turi ishlatiladigan o'rnatish usuli turiga mos kelishi va IEC 61730 va Xavfsizlik sinfi II talablariga javob berishi kerak.

• Izolyatsiya darajasi: 1,8 kV (o'tkazgich-o'tkazgich).
• Harorat: kamida -40 ° C dan + 90 ° C gacha (-40 ° F dan 190 ° F gacha).
• Supero'tkazuvchilar konstruktsiyasi: mis tozaligi 99,9% dan yuqori bo'lgan qalayli simli mis sim.
• Birlamchi izolyatsiya: o'zaro bog'langan polietilen (XLPE), quyosh nuri va namlikka chidamli, olovga chidamli. Er ostiga o'rnatilgan quvurlar va o'tish yo'llari uchun javob beradi.
• Izolyatsiya (ko'ylagi): termoplastik, quyosh nuriga chidamli, olovga chidamli, suvga chidamli.
• Izolyatsiyali kabelning minimal tashqi diametri - 5,2 mm (2,05 dyuym).
• Minimal Supero'tkazuvchilar tasavvurlar - 4 mm² (12 AWG).

SoliTek o'rnatuvchilarga faqat PV tizimlarida to'g'ridan-to'g'ri oqim (DC) simlari uchun malakali quyosh nuriga chidamli kabellardan foydalanishni tavsiya qiladi. Kabellar o'rnatish strukturasiga kabel va/yoki modulning mexanik shikastlanishiga yo'l qo'ymaslik uchun o'rnatilishi kerak. Kabellarga stress qo'ymang. O'rnatish uchun quyosh nuriga chidamli simi tasmalari va/yoki simni boshqarish kliplari kabi mos vositalardan foydalaning. Kabellar quyosh nuriga chidamli va suv o'tkazmaydigan bo'lsa-da, iloji bo'lsa, to'g'ridan-to'g'ri quyosh nuri ta'siridan va kabellarni suvga botirishdan saqlaning.
Birlashma qutilaridan kabellarning standart uzunligi 1,2 m (47,24 dyuym). Tizimda ikkita panel o'zaro bog'lanishi ko'zda tutilgan.

Tuproqlash

• Module grounding must be done in accordance with the electrical design and construction specifications, procedures, regulations and other special grounding requirements applicable to the installation sites. If grounding is needed, it should be done accordingly:

Framed type modules grounding
Ramkada topraklama belgisi bilan belgilangan teshiklar faqat topraklama uchun ishlatilishi mumkin. Modul ramkasida qo'shimcha topraklama teshiklarini burg'ulamang.
The grounding conductor or strap may be copper, copper alloy, or any other material acceptable foruse as an electrical conductor in accordance with local electric codes and regulations.
Keyin topraklama o'tkazgich mos keladigan topraklama elektrodi yordamida erga ulanishi kerak.
A bolted connection is required; it incorporates:

• Bolt o'lchami M4.
• Bolt boshi ostidagi tish yuvish mashinasi yoki tishli murvat anodlangan ramka kabi o'tkazmaydigan qoplamalarga kirishi kerak.
• M4 murvatiga mos keladigan gayka.
• Barcha jihozlar rangli metalldan, 300 seriyali zanglamaydigan po'latdan yoki mos ravishda korroziyadan himoyalangan bo'lishi kerak.
• Gaykani qulflashning tavsiya etilgan momenti 2 Nm÷2.2 Nm (1,48÷1,62 fut-lb).
• Topraklama murvati barcha ulanish elementlaridan o'tishi kerak.

• PV modullarining metall ramkalarini yerga ulash uchun sanab o'tilgan va aniqlangan qurilmalarga modulning ochiq metall ramkalarini tuproqli o'rnatish tuzilmalariga erga ulashga ruxsat beriladi.
• In any case the grounding screws or other parts have to be used separately from the mounting parts of the module.
• Alternate grounding options built through the mounting system are acceptable as long as they have been IEC and UL approved.
• Grounding resistance of the grounding structure shall be reached according to local regulations, Eurocodes, or other legal normative references.

Frameless type modules grounding

• Due to that modules are without frame, grounding is not forseen. Other PV plant equipment should be grounded according to the local and national electrical codes.

ULANuvchilar

• Connectors for SoliTek PV panels are Stäubli MC4-Evo 2. Keep connectors dry and clean and ensure that connector caps are hand-tight before connecting the modules.
• Ho'l, iflos yoki boshqa nosoz ulagichlar bilan elektr tarmog'iga ulanishga urinmang.
• Ulagichlarni quyosh nuri ta'siridan va suvga botirishdan saqlaning. Ulagichlarni erga yoki tom yuzasiga qo'ymang.
• Do not disconnect under load. Faulty connections can result in arcs and electrical shock.
• Barcha elektr ulanishlari mahkam o'rnatilganligini tekshiring. Barcha qulflash ulagichlari to'liq ulangan va qulflanganligiga ishonch hosil qiling.

BYPASS DIODLARI

The PV module’s junction box contains 3 bypass diodes (one in each part of split junction box; Schottky type) connected in parallel with the PV cell strings. In the case of partial shading (hot-spot effect), the diodes bypass the current generated by the non-shaded cells, therebylimiting module heating and performance losses.
Bypass diodlari haddan tashqari oqimdan himoya qiluvchi qurilmalar emas. Bypass diodlari qisman soya bo'lsa, oqimni hujayra satrlaridan boshqaradi. Ushbu diodlarning xususiyatlari:

• jildtage reyting - 50 V.
• Joriy reyting - 25 A.

Yong'inga qarshi SINFI

• SoliTek SOLID Bifacial va Blackstar modullari IEC yong'inga qarshi sinovi tomonidan tasdiqlangan va Yonuvchanlik klassi A ga erishgan. Yong'in sinovi IEC 127-5 ning A.300 bandida ko'rsatilganidek, 11,81 mm (2.5 dyuym) uchun 61730 mm (2 dyuym) moyillikda o'tkazildi.
• SoliTek SOLID Bifacial has fire rating of 28 according to UL1703-2 standard. SoliTek Blackstar has fire rating of 29 according to UL1703-2 standard.

Mexanik o'rnatish

• The mechanical loads described in this manual are the test loads.
• For calculating the equivalent maximum design loads, a safety factor of 1.5 (Design load×1.5 safety factor=Mechanical test load) needs to be considered in compliance with the requirements of the local laws and regulations.

UMUMIY TALABLAR

• Modules can be mounted in landscape or portrait orientation. For the bifacial modules, in order to get notable bifacial gain, the distance between the bottom of the modules and the roof or ground surface shall be at least 0,8 m (31,50 inch).
• Also, the bifacial gain increases significantly if modules are installed above white, light-reflecting surfaces (under surfaces with high albedo value).
• If the mounting rails are installed across the module, the bifaciality effect will be lower due to back-side cells shading.
• Iltimos, o'rnatish tizimiga kiritilgan xavfsizlik qoidalari va o'rnatish yo'riqnomalariga rioya qiling. Agar kerak bo'lsa, qo'shimcha ma'lumot uchun to'g'ridan-to'g'ri etkazib beruvchiga murojaat qiling.
• The modules must be safely set onto the mounting rail.
• The whole rail supporting the photovoltaic system must be strong enough to resist potential mechanical pressures caused either by wind or snow, in accordance with local, regional and state safety (and other associated) standards.
• The mounting system shall be tested and inspected by a third-party testing institution with static mechanical analysis capacity in accordance with local national standards or international standards.
• Before installing modules on a roof, ensure that the roof construction is suitable.
• In addition, any roof penetration required to mount the modules must be properly sealed to prevent leaks.
• O'rnatish temir yo'li termal kengayish natijasida kengayganida modullarga ta'sir qilmasligiga ishonch hosil qiling.
• The module can appear thermal expansion and cold contraction; thus, the interval between two adjoining modules shall be no lesser than 10 mm (0,39 inch).
• Shisha yuzasida va modullarning ramkalarida teshik ochishga urinmang, chunki bu kafolatni bekor qiladi.
• The mounting method must not result in the direct contact of dissimilar metals with the aluminum frame of the modules that will result in galvanic corrosion.

O'rnatish qismlari bardoshli, korroziyaga qarshi va UVga chidamli materiallardan tayyorlanishi kerak (zanglamaydigan po'lat va anodlangan alyuminiy komponentlar tavsiya etiladi).

CL BILAN O'rnatishAMPS

• Kamida 4 cl laminatdan foydalaningamps modullarni o'rnatish relslarida tuzatish uchun. Modullar clampning metall qismlari old yoki orqa oynaga tegmasligi kerak. Ushbu turdagi cl ni tanlashdaamp-montaj usuli, kamida to'rt cl foydalaningamphar bir modulda s; ikki clamps har bir uzun tomondan biriktirilishi kerak. Mahalliy shamol va qor yuklariga qarab, qo'shimcha clamps modullarning yukni ko'tara olishini ta'minlash uchun talab qilinishi mumkin.
• Clamps tortish momenti kamida 15 Nm (11,06 fut-lb) bo'lishi kerak, lekin 20 Nm (14,75 fut-lb) dan oshmasligi kerak. Odatda, 15 Nm (11,06 fut-lb), ikkita alyuminiy pro bo'lganda erishiladifilebir-biriga teginish. Agar modul >45° nishabga ega bo'lgan tomga portret yo'nalishida o'rnatilgan bo'lsa, modulning pastki qismida qo'shimcha ilgak kerak bo'ladi.

SOLID Black, Semi-clear, Satin, Agro Frameless

Transvers relslar bilan

BLACKSTAR, SOLID Black 35(40) mm, SOLID Semi-clear 35(40) mm, SOLID Satin 35(40) mm, SOLID Agro 35(40) mm, Magnus Framed mounting

• Ushbu turdagi cl ni tanlashdaamp-montaj usuli, kamida to'rt cl foydalaningamphar bir modulda s; ikki clamps modulning har bir tomoniga biriktirilishi kerak. Modullar clamps old oynaga tegmasligi va ramkani deformatsiya qilmasligi kerak.
• cl modulidan quyosh batareyalariga soya ta'siridan qochishingizga ishonch hosil qilingamps.
• The module frame is not to be modified under any circumstances. Do not to block the drain hole of the frame.
• Cl uzunligiamp should be at least 30 mm (1,18 inch).
• Clamp modul ramkasini kamida 5 mm (0,2 dyuym), lekin 10 mm (0,4 dyuym) dan oshmasligi kerak.

Transvers relslar bilan

Transversal relslarsiz yoki relslar uzun yon ramkaga perpendikulyar

O'rnatish tizimi bilan

Boltlar bilan o'rnatish

• Modul ko'ndalang chiziqlardagi ko'rsatilgan o'rnatish teshiklari orqali to'rtta M8 zanglamaydigan po'latdan yasalgan murvat bilan biriktirilishi va qo'llab-quvvatlanishi kerak. Kldagi momentamp bolt has to be in range of 8÷10 Nm (5,9÷7,38 ft-lb). The transversal bars positioning is shown in Figure 3.
• If additional mounting points are required, depending on the local wind and snow loads, then a mounting solution with clampuskuna tanlash kerak.

• Mounting with bolts can be done only through dedicated predrilled holes in the frame.
• Yangi teshiklarni burg'ulash taqiqlanadi va kafolatni bekor qiladi.

BOG'LANISH QUTISINING POZIYASI

• Birlashma qutisi va modul cheti orasidagi masofa yoki ulanish qutisi holati va maydonlarining boshqa o'lchamlari uchun quyida ko'rsatilgan raqamlarga qarang.

XIZMAT

• Modulning optimal ishlashini ta'minlash uchun SoliTek quyidagilarni tavsiya qiladi:
• Agar kerak bo'lsa, modulning shisha old qismini suv va yumshoq shimgich yoki mato bilan tozalash mumkin.
• Yana o'jar dog'larni olib tashlash uchun yumshoq, abraziv bo'lmagan yuvish vositasidan foydalanish mumkin.
• Elektr va mexanik ulanishlarni vaqti-vaqti bilan tekshiring va ular toza, xavfsiz, to'liq va xavfsiz ekanligiga ishonch hosil qiling.
• Muammo yuzaga kelgan taqdirda, litsenziyalangan/malakali shaxs bilan maslahatlashing.

XUSUSIYATLAR

Table 9. Electrical and mechanical parameters table.

Table 10. Electrical and mechanical parameters table.

Table 11.Electrical and mechanical parameters table.

• The electrical characteristics are within of the indicated values of ISC (φISC) ±3%, VOC (ϕVOC) ±3,5% and PMPP (ϕPmax) ±5%, under Standard Test Conditions (STC) (irradiance of 1000 W/m²,AM 1.5 spectrum, and a cell temperature of 25°C / 77°F)
• Barcha SoliTek SOLID PV panellari elektr xavfsizligi II sinfiga mos keladi.

Mas'uliyatdan voz kechish

• SoliTek ushbu ko'rsatmalarga muvofiq fotovoltaik tizimni o'rnatish, ishlatish, qo'llash va texnik xizmat ko'rsatishni nazorat qila olmasligi sababli. SoliTek mas'uliyatni o'z zimmasiga olmaydi va bunday o'rnatish, ishlatish, foydalanish yoki texnik xizmat ko'rsatish bilan bog'liq yoki har qanday tarzda kelib chiqadigan har qanday yo'qotish, zarar yoki xarajatlar uchun javobgarlikni o'z zimmasiga olmaydi.
• SoliTek will not take any responsibility for any possible violation of patent rights and third-party rights that are related to the application of the solar energy system. No permission of patents is given through implication.
• The information of this instruction is from the knowledge and experiences of SoliTek. However, the instructions and suggestions of this instruction do not make an external or internal of guarantee. SoliTek reserves the right to revise this instruction, products and all the information about products without prior notification to customers.

www.solitek.eu

TSS

• Q: What should I do before installing the PV modules?
  • A: Read this entire guide, understand all instructions, and ensure compliance with all local, state, and federal regulations. Consult a certified building specialist for the structural integrity of the dwelling.
• Q: Can I install the PV modules myself without professional training?
  • A: This documentation is not a complete installation manual for personnel not specifically trained in PV-modules. It serves as a general but strictly mandatory reference for the installer. Professional installation is highly recommended.
• Q: What happens if I don’t follow the instructions in this guide?
  • A: Failure to follow instructions may damage system components, endanger personnel, damage property, or invalidate the panel warranty.
• Q: Is it safe to work on a rooftop during installation?
  • A: Do not attempt to work on a rooftop until safety precautions have been identified and taken, including fall protection measures, ladders or stairways, and personal protective equipment (PPE). Avoid adverse conditions like strong winds or wet/frosted roofs.
• Q: How should I store the PV modules before installation?
  • A: Store pallets in a cool and dry location until the PV modules are ready to be unpackaged. Do not exceed the maximum stacking height indicated on the packaging.