YO'LLASHNI O'RNATISH
CSEN1
CSEN1 Combo Sensor Controller
Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)
TAVSIF
The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.
XUSUSIYATLAR
- Radiochastota: 2.4 GHz (IEEE 802.15.4)
- RF uzatish chiqish quvvati: +20dBM
- Ishlash harorati: -40 ° dan +70 ° C gacha
- Ishlaydigan namlik: 10 dan 95% gacha, kondensatsiyalanmaydi
- IP66 nominal muhofazasi
- Olchamlari: 3.1” D x 1.6” H (80 mm D x 42 mm H)
- Input Power: 12-24VDC, 35mA max, 840mW
- Nazoratning maqsadi: Operatsion
- Environmental: Indoor/Outdoor
- Ifloslanish darajasi: 3
- Reyting Impulse Voltage: 330V
DIZAYN HAQIDAGI MULOKLAR
Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltagDC 10V kuchlanishli.
- Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
- Iloji bo'lsa, karartma simlarini AC liniyalaridan uzoqroqqa o'tkazing.
- Har bir kontroller uchun maksimal 4 ta DALI-2/D4i LED drayverlari, agar kattaroq nisbat kerak bo'lsa, Synapse Support bilan maslahatlashing.
- Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
- Issiqlik moslamasiga yoki LED drayveriga o'rnatmang.
ESLATMA: LED drayveri DIM to OFF funksiyasini qo'llab-quvvatlashi kerak.
OGOHLANTIRISH VA Ogohlantirishlar
- TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
- Ushbu ko'rsatmalar va ogohlantirishlarga rioya qilmaslik kafolatni bekor qilishi mumkin.
- This product must be installed in accordance with national, state, and local electrical codes and requirements.
- If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.
ZHAGA KITOB 18 ROZETA BO'YICHA QUVVATLASH MA'LUMOTI
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:
- 12-24VDC POWER: Brown
- Common Ground/DALI-: Pink with White Stripe
- DALI+/DIM+: Violet with White Stripe
- Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length
1-rasm 
O'RNATISH BO'YICHA KO'RSATMALAR
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
- Iloji bo'lsa, moslama idishida o'rnatilgan muhrlangan qopqoq yoki yoritishni boshqarish moslamasini olib tashlang.
- Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
- After alignment, push until the CSEN1 is fully seated within the receptacle.
- While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)
Eslatma: To'g'ri ishlashi uchun kontroller rozetkaga to'liq o'rnatilganligiga va qulflangan holatga o'ralganligiga ishonch hosil qiling.
Ogohlantirish: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
2-rasm
STATUS LEDlari
| Quvvatli LED | Status |
| Moviy | On for 3 seconds at Startup, then Off |
| LED holati | Status |
| Qizil | No script on the device |
| Miltillovchi qizil | Aloqa xatosi |
| Miltillovchi koʻk | Communication, No Config |
| Miltillovchi yashil | Normal Operation with Motion |
| Oʻchirilgan | Normal Operation, no Motion |
NORMATIV MA'LUMOTLAR VA SERTIFIKATLAR
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada (IC) sertifikatlari: Ushbu raqamli qurilma Kanada Aloqa Departamentining Radio shovqinlari qoidalarida belgilangan raqamli qurilmalardan radio shovqin chiqarish uchun B sinfi chegaralaridan oshmaydi.
FCC sertifikatlari va me'yoriy ma'lumotlar (faqat AQShda)
FCC 15-qism B sinfi: Ushbu qurilma FCC qoidalarining 15-qismiga mos keladi. Ishlash quyidagi ikkita shartga bo'ysunadi: (1) Bu qurilmalar zararli shovqinlarni keltirib chiqarmasligi mumkin va (2) Ushbu qurilmalar qabul qilingan har qanday shovqinni, jumladan, zararli ishlashga olib kelishi mumkin bo'lgan shovqinlarni qabul qilishi kerak.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:
- 15-qism, B kichik bo'limi, B sinfidagi uskunalar uchun
- FCC 96-208, chunki u B sinfidagi shaxsiy kompyuterlar va tashqi qurilmalarga tegishli
- Ushbu mahsulot FCC qoidalariga muvofiq sertifikatlangan tashqi sinov laboratoriyasida sinovdan o'tkazildi va FCC, 15-qism, Emissiya chegaralariga javob berishi aniqlandi. Hujjatlar yoqilgan file va Synapse Wireless, Inc.dan foydalanish mumkin.
Agar ushbu mahsulot korpusidagi modul uchun FCC identifikatori boshqa qurilma ichiga o'rnatilganda ko'rinmasa, ushbu mahsulot o'rnatilgan qurilmaning tashqi tomonida ham FCC ID moduliga tegishli yorliq ko'rsatilishi kerak. O'zgartirishlar (FCC 15.21):
Synapse Wireless, Inc. tomonidan aniq tasdiqlanmagan ushbu uskunaga kiritilgan o'zgartirishlar yoki modifikatsiyalar foydalanuvchining ushbu uskunani ishlatish huquqini bekor qilishi mumkin.
Patentlangan - virtual belgilash da https://www.synapsewireless.com/about/patents
Qo'shimcha ma'lumot olish uchun tashrif buyuring: synapsewireless.com
SERTIFIKATLAR
| Model | CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure) |
| FCC identifikatorini o'z ichiga oladi | QOQ-GM240P |
| IC o'z ichiga oladi | 5123A-GM240P |
| RoHS 3 | 2011/65/EU (2015/863) |
| EI REACH | (EC) No 1907/2006 |
DALI-2 sertifikatlangan ilovalar boshqaruvchisi
Hujjatlar / manbalar
 |
Synapse CSEN1 Combo Sensor Controller [pdf] Oʻrnatish boʻyicha qoʻllanma CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller |