USAutomatic Low Current Receiver Installation Guide

USAutomatic Low Current Receiver

Ushbu mahsulotni tanlaganingiz uchun tashakkur.
Iltimos, ushbu mahsulotni o'rnatishdan oldin ushbu qo'llanmani diqqat bilan o'qing.

Kirish

• 030205 past oqim qabul qiluvchi elementi AM/ASK modulyatsiyasida 2 MGts chastotada ishlaydigan 433,92 o'rni chiqish qabul qiluvchisi.
• Bu juda kam dam olish oqimi iste'moli bilan avtomatik yopish tizimlari va o'g'rilikka qarshi tizimlar uchun mo'ljallangan.
• The operating frequency is among the European harmonised frequencies. The antenna is connected with a F- type connector.
• O'rnimizni chiqishlari faqat YO'Q kontaktli umumiy kontaktni Yerga qisqa tutashgan holda.
• K1 ning ish rejimi Pulse va K2 ning ish rejimi Pulse yoki Latch bo'lishi mumkin. Quvvat manbai 12 Vdc.
• 2X IP darajasi faqat ichki o'rnatishga ruxsat beradi.
• Mahsulot EMC Yevropa qoidalariga (CE) va FCC 15-qism qoidalariga toʻliq javob beradi.

Foydalanadigan transmitterlar

• 2-button transmitter – Part # 030210
• 4-button transmitter – Part # 030212

Texnik spetsifikatsiyalar

• Qabul qiluvchi turi: Superheterodin.
• Demodulyatsiya: AM/ASK.
• Ishlash chastotasi: 433,92 MGts.
• Mahalliy osilator chastotasi: 6,6128 MGts.
• O'rtacha chastota: 10,7 MGts.
• Sezuvchanlik (yaxshi signal uchun): -115 dBm.
• Kirish empedansi: 75 Ohm.
• Ta'minot hajmitage: 12 dc ( ± 10% ).

Hozirgi yutilish:

• dam olishda: 1.5 mA
• 1 o'rni bilan hayajonlangan: 7 mA
• O'rni soni: 2 (1NO, 1NO).
• O'rni ish rejimi Pulse / Latch
• Commutable max power: 24W or 24VA.
• Xotira hajmi (tx tugmalari): 42.
• Operating temperature: -4 ÷ +158 °F.
• Olchamlari: 4.13 x 1.77 x 1.1 dyuym
• Og'irligi: 2.29 oz
• IP himoya darajasi: 2X

Qabul qilgich tugadiview

• P1 : P1 tugmasi
• P2 : P2 tugmasi
• LD: Green Led
• CON: I/O Connector
• K1: Relay 1 chiqishi
• F: F tipidagi ulagich
• K2: Relay 2 chiqishi

Ulanish diagrammasi

Asosiy xususiyatlar

• Juda kam dam olish oqimi iste'moli
• 42 ta saqlanadigan uzatuvchi kalitlari
• Bitta transmitter kaliti yoki To'liq xotirani o'chirish
• 2 ta o'rni dasturlashtiriladigan ish rejimi: lahzali, qulflash
• Oson transmitter dasturlash

TRANSMITER VA QABUL QILGANNI DASTURLASHTIRISH

• The Transmitter and Receiver operate at 433 MHz. The receiver can store up to 22 unique transmitter codes.

Transmitterni sozlash:
(Dipswitchlarni standart sozlamalardan o'zgartirish tavsiya etiladi)

1. Batareya bo'limining eshigini oching va o'zgartirish tugmachalarini toping.
2. Dipswitchlarni o'zingiz yoqtirgan sozlamalarga o'zgartiring. Kelajakda foydalanish uchun yozib oling.

Qabul qiluvchini dasturlash uchun transmitterning chap tugmasi:
(standart ochish/to'xtatish/yopish funksiyasi)

1. Press and hold the left transmitter button down. Red light on the transmitter should be on.
2. Qabul qilgichdagi yashil LD chirog'i yonmaguncha P1 tugmachasini bosing.
3. Ikkala tugmani ham qo'yib yuboring. Transmitterning chap tugmachasini qabul qiluvchiga dasturlash tugallandi.

Qabul qiluvchini dasturlash uchun uzatuvchi o'ng tugmasi:
(Hold-Gate-Open) (Faqat avtomatik yopish taymeri yoqilgan bo'lsa)
The 2-channel receiver allows for programming the P2 relay from momentary mode (default) to latching mode. The transmitter right button can then be programmed to hold the gate open, overriding the auto-close feature, if activated.

1. Press and hold the right transmitter button down. Red light on the transmitter should be on.
2. Qabul qilgichdagi yashil LD chirog'i yonmaguncha P2 tugmachasini bosing.
3. Ikkala tugmani ham qo'yib yuboring.
4. Transmitterning o'ng tugmachasini qabul qiluvchiga dasturlash tugallandi.
5. Endi siz P2 qabul qilgichni quyidagi bosqichlarda qulflash rejimiga o'rnatishingiz kerak.

Qabul qiluvchilarni dasturlash:
P2 o'rni dasturlashni bir lahzalikdan qulflash rejimiga o'tkazish (eshikni ochiq ushlab turish uchun)

1. Qabul qilgichdagi P2 tugmachasini yashil LD chirog'i yonmaguncha bosing va keyin qo'yib yuboring. Yashil LD nuri barqaror bo'lishi kerak.
2. Yashil LD chirog'i yoqilganda, P1 tugmachasini pastga bosing va qo'yib yuboring. Yashil LD chirog'i miltillashi kerak. Latch rejimi o'rnatildi.

P2 qabul qiluvchining relesi qulflash rejimiga dasturlashtirilganligini tekshirish:

1. Qabul qilgichdagi P2 tugmachasini yashil LD chirog'i yonmaguncha bosing va keyin qo'yib yuboring.
2. Yashil LD chirog'i miltillashi kerak. Yashil LD chirog'i doimiy bo'lsa, yuqoridagi Qabul qiluvchilarni dasturlash bo'limini qayta bajaring.

Qabul qiluvchining P2 o'rni vaqtinchalik rejimga o'rnatilishi:

1. Qabul qilgichdagi P2 tugmachasini yashil LD chirog'i yonmaguncha bosing va keyin qo'yib yuboring. Yashil LD chirog'i miltillashi kerak.
2. Yashil LD chirog'i yoqilganda, P1 tugmachasini pastga bosing va qo'yib yuboring. Yashil LD chiroq qattiq bo'lishi kerak. Vaqtinchalik rejim o'rnatilgan.

Erasing Qabul qiluvchi xotiradan bitta uzatuvchi:
O'chirish uchun transmitterning dipswitch sozlamalari ma'lum bo'lishi kerak.
Agar ma'lum bo'lsa, quyidagi amallarni bajaring.

1. O'chirish uchun transmitter kodining kalit sozlamalariga mos keladigan transmitterdagi dipswitchlarni o'rnating.
2. Chap transmitter tugmasini bosing va ushlab turing.
3. Yashil LD chirog'i yonmaguncha qabul qilgichdagi P1 tugmachasini bosing.
   Keyin ikkalasini ham qo'yib yuboring.
4. O'ng transmitter tugmasini bosing va ushlab turing.
5. Yashil LD chirog'i yonmaguncha qabul qilgichdagi P2 tugmachasini bosing.
   Keyin ikkalasini ham qo'yib yuboring.
6. Transmitter endi qabul qiluvchi xotirasidan o'chiriladi.

Erasing qabul qiluvchi xotirasidagi barcha transmitterlar:

1. Yashil LD chirog'i yonmaguncha qabul qilgichdagi P2 tugmasini bosing. Keyin P2 tugmasini qo'yib yuboring.
2. LD chirog'i yoqilgan paytda P1 va P2 tugmalarini bir vaqtning o'zida bosing va yashil LD chirog'i sekin miltillay boshlaguncha ushlab turing.
3. U 4 marta miltillashi kerak, keyin barcha transmitter kodlari o'chiriladi.

TRANSMITER RAQAMI KO'RSATI

• Xotirada qancha transmitter kalitlari saqlanganligini ko'rsatish mumkin.
• Raqam ikkilik yozuvda ( 0 yoki 1 ) diodli miltillashlar ketma-ketligi bilan ko'rsatiladi.
• LDning qisqa miltillashi (½ soniya) ikkilik “0” ni beradi.
• LD ning uzoq miltillashi (1 soniya) ikkilik "1" ni beradi.
• To'liq ketma-ketlik 6 marta miltillashdan va oxirgi uzunroq miltillashdan (2 soniya) iborat.
• Uning pozitsiyasiga ko'ra, har bir chirog'ning turli xil "og'irligi" bor.

First flash: 2 = 1

1. Second flash: 2 = 2
2. Third flash: 2 = 4
3. Fourth flash: 2 = 8
4. Fifth flash: 2 = 16
5. Sixth flash: 2 = 32

Jarayon

1. LD yoqilguncha P1 yoki P2 tugmalarini bosib turing.
2. Tugmani qo'yib yuboring va LD o'chguncha P2 tugmasini bir muddat bosib turing.

Shu nuqtada miltillashlar ketma-ketligi boshlanadi.
Quyidagi misolda ko'rsatilganidek, mos keladigan o'nlik sonni hisoblash uchun ketma-ketlikka e'tibor beringamples.

Es. № 1: Xotira bo'sh

• Og'irliklar 1 2 4 8 16 32 Oxirgi ketma-ketlik
• Ketma-ketlik: _ _ _ _ _ ________
• Final number : 0 + 0 + 0 + 0 + 0 + 0 = 0

Es. № 2: 5 transmitter tugmalari

• Og'irliklar 1 2 4 8 16 32 Oxirgi ketma-ketlik
• Ketma-ketlik: __ _ __ _ _ ________
• Yakuniy raqam: 1+ 0 + 4 + 0 + 0 + 0 = 5

Es. № 3: 12 transmitter tugmalari

• Og'irliklar 1 2 4 8 16 32 Oxirgi ketma-ketlik
• Ketma-ketlik: _ _ _ __ _ _ ________
• Yakuniy raqam: 0 + 0 + 4 + 8 + 0 + 0 =12

KAFOLAT

• USAutomatic, LLC warrants this product to be free of defects in materials and workmanship for 1 YEAR. For a period of 1 YEAR following purchase, USAutomatic, LLC. will repair or replace the product free of charge, including parts, shop labor and return to customer shipping and handling.
• This 1-year warranty does not cover the plastic case from normal wear or damage due to misuse.
• To have the product sent for warranty consideration, it must be returned with the proof of purchase and a return authorization number. To obtain a return authorization number, please call 1-888-204-0174 for assistance. The return authorization number must be clearly marked on the outside of the return package or it may not be accepted.

ALOQA

• www.usautomaticgateopeners.com
• (888)-378-1170
• sales@usautomaticgateopeners.com